State Industries Electric Heater GPO69 700 User Manual

C O M M E R C I A L  
TITAN  
Commercial Oil Water Heater  
Meets or Exceeds the Thermal Efficiency and/or Standby Loss  
Requirements of the U.S. Department of Energy and Current  
Edition of ASHRAE/IESNA 90.1  
TitanModels Inhibit Lime and Sediment Buildup –  
Titanmodels are warranted against tank failure due to sediment buildup for three years.  
Glass-Lined Tank – Assures years of rust-free clean hot water. 160 psi working pressure.  
180° Adjustable Thermostat – Has upper and lower sensing bulbs to average  
water temperatures at top and bottom of heater for maximum temperature control (120°-180°).  
Safety Shutoff – Limits temperature buildup.  
UL Listed Oil Burner – Precision engineered to match the units they are used  
with; designed to fire 1.75 to 5.0 gallons of oil per hour. All models equipped with single phase  
continuous duty motor 120 volt AC 60 Hz, 3450 rpm with overload switch and interrupted  
ignition. Standard burners equipped with single stage pump with 1 or 2 line capability.  
Flame retention principle assures high rate of combustion efficiency, yet maintains low  
operating noise levels. Fuel unit includes pump, strainer, pressure regulating valve and  
ignition transformer. Transformer rated at 120 volt AC, 60 Hz with high voltage secondary,  
UL listed for use with No. 1 and 2 commercial grade fuel oil. Burner mounted cadmium  
cell relay for flame detection - 15 second safety switch timing eliminates the need for  
RA890F Electronic Safeguard. Complies with UL 296-MP 1192.  
Efficient Combustion Chamber – Precast, high temperature combustion chamber  
made of alumina silica ceramic fiber. Engineered for maximum insulation and heat reflection.  
Unique design assures more complete combustion by stabilizing flame pattern.  
Interrupted Ignition – Reduces electrical consumption.  
Oil Solenoid Safety Valve – Standard on GPO75 385, GPO75 455 and GPO69 700.  
3/4” Drain Valve – Provided in lower tank for fast draining.  
Two Hand-Hole Cleanouts – Allows easy cleaning on standard models GPO75 385  
and larger and ASME models.  
Anodic Protection – For longer tank life.  
Flame Observation Port – Permits convenient flame check.  
Foam Insulation – Saves fuel, helps assure constant temperature, vermin proof.  
Jacket – Heavy gauge steel with baked enamel finish over bonderized undercoat. Not  
approved for installation on combustible flooring.  
Easy To Install Burner – Three bolt mounting of burner assures easy installation.  
Barometric Draft Regulator  
CSA Certified and ASME Rated T&P Relief Valve  
CAUTION: Units must be installed on non-combustible surface.  
Limited Warranty:  
Limited Warranty Outline  
If the tank should leak any time during the first three  
years, under the terms of the warranty, State Water  
Heaters will furnish a replacement heater; installation,  
labor, handling and local delivery extra.  
Other Features:  
Two layers of high temperature ceramic fiber insulation in combustion chamber  
Flame inspection port opening  
Mounted on rugged channel iron skids  
Multiple anodes for protection  
Optional Features:  
– Two Stage Pump – For use with underground oil storage tanks.  
– ASME Construction – Available on models GPO84 315, GPO75 385, GPO75 455,  
GPO69 700. ASME units have 160 psi working pressure.  
– NOTE: This Outline Is NOT A Warranty. For  
complete information, consult the written  
warranty or State Water Heaters.  
For more information on Titancontact:  
State Water Heaters  
500 Tennessee Waltz Parkway, Ashland City, TN 37015  
800-365-0024 Toll-free USA  
SCOSS00105  
July 2008R  
 

Sharp Car Video System PN K321H User Manual
Sharp Flat Panel Television LC 45GD5U User Manual
Sony Laptop VPCY21BGX B User Manual
Sony MP3 Player DSX A30 User Manual
Sony Stereo Receiver 3 289 204 423 User Manual
Sony Stereo System CMT EP30 User Manual
Sunbeam Blender PB2000 User Manual
Swann Camcorder SW211 DPE User Manual
Swann TV Receiver SW112 DVB User Manual
Tannoy Portable Speaker Highline 500 User Manual