State Industries Electric Heater Gas User Manual

Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters  
Meets or exceeds current edition of ASHRAE/IES-90.1-1999.  
Low NOX – TPX Low NOX models meet or exceed current Texas and  
California SCAQMD air quality standards.  
UL – Entire unit UL listed (File No. MH11631).  
Glass-Lined Tank – Exclusive corrosion protection with glass-  
lining on all interior surfaces. Multiple anodes provide even more  
corrosion protection.  
ASME Construction Standard – 160 PSI working pressure on all models.  
Powered Gas Burner – Powered burner has electronic flame  
safeguard control with intermittent spark ignition. Also included are  
main and pilot automatic gas valves plus gas pressure regulators,  
diaphragm air switch for proof of blower operation.  
TPX Low NOX Models are factory standard with modulating fire.  
The burner automatically adjusts the firing rate and the Btu output  
to maintain precise system temperature control.  
Fully Automatic Controls With Safety Shutoff – High temperature  
limit control (manual reset). ASME rated temperature and pressure  
relief valve. Hinged door control compartment for ease of access. Two  
thermostats, upper and lower, for accurate temperature control.  
Standard control is for 120˚F - 180˚F water service.  
Jacket And Insulation – Heavy gauge steel with baked powder coat  
finish. Insulated with high-density foam insulation that meets or  
exceeds all required standards.  
Professional Start-Up Service Furnished To Assure Most Efficient  
Combustion And Safe Initial Start-Up.  
Other Features  
Two layers of high temperature ceramic fiber insulation in  
combustion chamber  
Limited Warranty Outline  
If the tank should leak any time during the first three years, under  
the terms of the warranty, State Water Heaters will repair or replace  
heater; installation, labor, handling and local delivery extra.  
– NOTE: This Outline Is NOT A Warranty. For complete information,  
consult the written warranty or State Water Heaters.  
Flame inspection port opening  
Mounted on rugged channel iron skids  
Combination temperature and pressure gauge  
Low water cutoff  
ASME rated temperature and pressure relief valve  
Barometric draft regulator  
Two cleanout inspection openings  
120 volt control circuit  
Drain valve  
TPO – Oil Fired Models: No. 1 or 2 Oil  
Multi-annular fuel containment combustor head  
Available for firing light fuel oils including diesel  
Oil ignition transformer  
Removable lifting lugs  
Integral 2-stage fuel unit  
Squirrel cage blower  
Oil safety valve  
Options  
Factory Mutual approved control arrangement  
Industrial Risk Insurance (IRI Gas Train)  
5 year or 10 year limited warranty  
High or low water pressure switch  
180°F water service thermostats  
A.G.A. rated T & P Valve  
Modular graphic burner systems management on heaters with  
270,000 Btu input and over  
Combustion Air intake Adapter  
TPD – Dual Fuel Gas/Oil: Natural Gas or Propane & No. 1 or 2 Oil  
Multi-annular fuel containment combustor head  
Gas electric pilot and gas ignition transformer  
Pilot and main pressure regulators  
Air safety switch  
Manual fuel selector switch  
Integral 2-stage fuel unit  
Squirrel cage blower  
COMMERCIAL  
The Expert’s Choice®  
 
TPX Power Low NO Large Volume Commercial Water Heaters  
X
SPECIFICATIONS  
Input  
Rating  
BTU/Hr.  
Natural  
Gas  
Nominal  
Storage  
Capacity  
U.S.  
Output (Gallons)  
Recovery  
Dimensions In Inches  
Motor HP  
120V 60 Hz 1  
Model Number  
First  
Hour  
Gallons  
Rating 80°F Rise 100°F Rise 140°F Rise  
A
B
C
D
E
F
G
H
J
T
PX 150 400 NEA  
150  
150  
200  
400,000 507  
540,000 644  
800,000 936  
485  
654  
970  
387  
524  
776  
277  
374  
554  
693  
866  
1039  
554  
693  
866  
1039  
554  
693  
866  
1039  
1212  
1385  
693  
8312 14  
8312 14  
8312 15  
8312 15  
8312 15  
8312 15  
9112 14  
9112 14  
9112 14  
9112 14  
9112 15  
9112 15  
9112 15  
9112 15  
9112 15  
9912 15  
119 15  
119 15  
119 15  
119 15  
119 15  
1
1
2734 114  
2734 114  
3212 112  
3212 112  
3212 112  
3212 112  
2612 112  
2612 112  
2612 112  
2612 112  
54  
54  
60  
60  
60  
60  
60  
60  
60  
60  
67  
67  
67  
67  
55  
55  
67  
67  
67  
55  
55  
7
8
5712 73  
1
7
HP - 2.5 Amps  
TPX 150 540 NEA  
TPX 200 800 NEA  
TPX 200 1000 NEA  
TPX 200 1250 NEA  
TPX 200 1500 NEA  
TPX 300 800 NEA  
TPX 300 1000 NEA  
TPX 300 1250 NEA  
TPX 300 1500 NEA  
TPX 400 800 NEA  
TPX 400 1000 NEA  
TPX 400 1250 NEA  
TPX 400 1500 NEA  
TPX 400 1750 NEA  
TPX 400 2000 NEA  
TPX 600 1000 NEA  
TPX 600 1250 NEA  
TPX 600 1500 NEA  
TPX 600 1750 NEA  
TPX 600 2000 NEA  
5712 73  
114  
114  
114  
112  
114  
114  
114  
112  
114  
114  
114  
112  
2
10  
10  
12  
12  
10  
10  
12  
12  
10  
10  
12  
12  
72  
72  
72  
72  
72  
72  
72  
72  
84  
84  
84  
84  
73  
73  
73  
73  
83  
83  
83  
83  
81  
81  
81  
81  
200 1,000,000 1130  
200 1,250,000 1372  
200 1,500,000 1615  
1212  
1515  
1818  
970  
1212  
1515  
1818  
970  
1212  
1515  
1816  
2121  
2424  
1212  
1515  
1816  
2121  
2424  
970  
1212  
1455  
776  
300  
800,000 1016  
300 1,000,000 1210  
300 1,250,000 1452  
300 1,500,000 1695  
970  
1
3
HP - 8.6 Amps  
1212  
1455  
776  
400  
800,000 1096  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
2
2
2
2
2
2
2
2
2
2
2
400 1,000,000 1290  
400 1,250,000 1532  
400 1,500,000 1775  
400 1,750,000 2017  
400 2,000,000 2259  
600 1,000,000 1450  
600 1,250,000 1692  
600 1,500,000 1935  
600 1,750,000 2177  
600 2,000,000 2419  
970  
1212  
1455  
1697  
1939  
970  
1212  
1455  
1697  
1939  
14 9112 81  
1 HP - 12.4 Amps  
2
14 9112 89  
114  
114  
112  
2
10  
12  
12  
84 109  
84 109  
84 109  
1
866  
3
HP - 8.6 Amps  
1039  
1212  
1385  
14 9112 109  
14 9112 109  
1 HP - 12.4 Amps  
2
Certified Minimum Installation Clearances to Combustibles:  
Front: 18 inches  
Back: 0 inches  
Sides: 0 inches  
Top: 5 inches  
ASME  
A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power  
burner, drain valve and anodes (anodes are located on side above cold water inlet).  
Minimum gas supply pressure: 7 Inches W.C.  
Maximum gas supply pressure: 13 Inches W.C.  
TPX models are Category I appliances (Fan Assisted) and require a negative draft. These units should  
only be commonly vented with other Category I negative draft appliances per the latest addition of the  
National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft  
of -0.02˝ to -0.07 is required in the vent.  
COMMERCIAL  
The Expert’s Choice®  
 
TPO Power Oil Large Volume Commercial Water Heaters  
SPECIFICATIONS  
Actual  
Ship.  
Output (Gallons)  
Recovery  
Dimensions In Inches  
Storage  
Capacity  
U.S.  
Input  
Rating  
BTU/Hr.  
Firing  
Rate  
GPH  
Wt.  
w/Burner  
(lbs.)  
Motor HP  
120V 60 Hz 1  
Model Number  
Gallons  
80°F Rise 100°F Rise 140°F Rise  
A
B
C
D
E
F
G
H
J
TPO 150 140 OEA  
TPO 150 199 OEA  
TPO 150 255 OEA  
TPO 150 270 OEA  
TPO 150 400 OEA  
TPO 150 540 OEA  
TPO 150 720 OEA  
TPO 200 300 OEA  
TPO 200 600 OEA  
TPO 200 800 OEA  
TPO 200 1000 OEA  
TPO 200 1250 OEA  
TPO 200 1500 OEA  
TPO 300 300 OEA  
TPO 300 600 OEA  
TPO 300 800 OEA  
TPO 300 1000 OEA  
TPO 300 1250 OEA  
TPO 300 1500 OEA  
TPO 400 600 OEA  
TPO 400 800 OEA  
TPO 400 1000 OEA  
TPO 400 1250 OEA  
TPO 400 1500 OEA  
TPO 400 1750 OEA  
TPO 400 2000 OEA  
TPO 500 2250 OEA  
TPO 500 2500 OEA  
TPO 600 720 OEA  
TPO 600 1000 OEA  
TPO 600 1250 OEA  
TPO 600 1500 OEA  
TPO 600 1750 OEA  
TPO 600 2000 OEA  
TPO 600 2250 OEA  
TPO 600 2500 OEA  
163  
163  
163  
163  
151  
151  
145  
221  
221  
221  
140,000  
199,000  
255,000  
270,000  
400,000  
540,000  
720,000  
300,000  
600,000  
800,000  
1
170  
241  
309  
327  
485  
654  
873  
364  
727  
136  
193  
247  
262  
387  
524  
698  
291  
582  
776  
970  
1212  
1455  
291  
582  
776  
970  
1212  
1455  
582  
776  
970  
1212  
1455  
1697  
1939  
2182  
2424  
698  
97  
138  
176  
187  
277  
374  
416  
208  
416  
554  
693  
866  
1039  
208  
416  
554  
693  
8312 14  
8312 14  
8312 14  
8312 14  
8312 14  
8312 14  
8312 14  
8312 15  
8312 15  
8312 15  
8312 15  
8312 15  
8312 15  
9112 14  
9112 14  
9112 14  
9112 14  
9112 14  
9112 14  
9112 15  
9112 15  
9112 15  
9112 15  
9112 15  
9112 15  
9912 15  
110 15  
110 15  
119 15  
119 15  
119 15  
119 15  
119 15  
119 15  
119 15  
119 15  
2734 114 3612  
2734 114 3612  
2734 114 3612  
2734 114 3612  
2734 114 3612  
2734 114 3612  
5
6
6
6
7
8
47 73  
47 73  
47 73  
5712 73  
5712 73  
5712 73  
1292  
1292  
1292  
1397  
1397  
1505  
1510  
2098  
2098  
2103  
2103  
2467  
2757  
2150  
2150  
2308  
2308  
2584  
2774  
3207  
3212  
3212  
3212  
3402  
3528  
3669  
1.4  
1.8  
1.9  
2.8  
3.8  
5.1  
2.1  
4.2  
5.7  
1
7
HP - 4.4 Amp  
1
1
2734 114 3612 10 5712 73  
4
3
HP - 4.6 Amp  
HP - 5.5 Amp  
3212 112 4434  
3212 112 4434  
6
8
6612 73  
6612 73  
970  
3212 112 4434 10 6612 73  
3212 112 4434 10 6612 73  
3212 112 4434 12 6612 73  
3212 112 4434 12 8112 73  
201 1,000,000 7.1  
201 1,250,000 8.9  
201 1,500,000 10.7  
300  
300  
300  
300 1,000,000 7.1  
300 1,250,000 8.9  
300 1,500,000 10.7  
411  
411  
411 1,000,000 7.1  
411 1,250,000 8.9  
397 1,500,000 10.7  
397 1,750,000 12.5  
397 2,000,000 14.2  
495 2,250,000  
495 2,500,000 17.8  
594 720,000 5.1  
594 1,000,000 7.1  
594 1,250,000 8.9  
594 1,500,000 10.7  
594 1,750,000 12.5  
594 2,000,000 14.3  
1212  
1515  
1818  
364  
727  
970  
1212  
1515  
1818  
727  
3
3
3
4
HP - 10.2 Amp  
HP - 4.6 Amp  
300,000  
600,000  
800,000  
2.1  
4.2  
5.7  
2612 112 4434  
2612 112 4434  
6
8
6612 83  
6612 83  
1
4
2612 112 4434 10 6612 83  
2612 112 4434 10 6612 83  
2612 112 4434 12 6612 83  
2612 112 4434 12 8112 83  
1
3
HP - 5.5 Amp  
866  
1039  
416  
554  
693  
4
HP - 10.2 Amp  
HP - 4.6 Amp  
1
600,000  
800,000  
4.2  
5.7  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
3212  
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
55  
8
7612 81  
4
970  
55 10 7612 81  
55 10 7612 81  
55 12 7612 81  
55 12 9112 81  
55 14 9112 81  
55 14 9112 89  
1
1212  
1515  
1816  
2121  
2424  
2727  
3030  
873  
1212  
1515  
1816  
2121  
2424  
2727  
3030  
3
HP - 5.5 Amp  
866  
1039  
1212  
1385  
1558  
1732  
499  
693  
866  
1039  
1212  
1385  
1558  
1732  
4  
HP - 10.2 Amp  
16  
55 16 9112 100 4277  
55 16 9112 100 4419  
55 10 7612 109 3667  
55 10 7612 109 3667  
55 12 7612 109 3667  
55 12 9112 109 3837  
55 14 9112 109 3837  
55 14 9112 109 3837  
55 16 9112 109 4477  
55 16 9112 109 4619  
1 HP - 16 Amp  
1
4
3
HP - 4.6 Amp  
HP - 5.5 Amp  
970  
1
1212  
1455  
1697  
1939  
2182  
2424  
3
4  
HP - 10.2 Amp  
575 2,250,000  
575 2,500,000 17.8  
16  
1 HP - 16 Amp  
Certified Minimum Installation Clearances to Combustibles:  
Front: 18 inches  
Back: 0 inches  
Sides: 0 inches  
Top: 5 inches  
A clearance of 24 inches should be maintained from  
serviceable parts such as relief valve, power burner, drain  
valve and anodes (anodes are located on side above cold  
water inlet).  
State Titan TPO models are Category I appliances  
(Fan Assisted) and require a negative draft. These units  
should only be commonly vented with other Category I  
negative draft appliances per the latest addition of the  
National Fuel Gas Code. An approved/listed Type “B” venting  
material is recommended. A negative draft of -0.02˝ to -0.07  
is required in the vent.  
ASME  
COMMERCIAL  
The Expert’s Choice®  
 
TPD Power Dual Fuel Large Volume Commercial Water Heaters  
SPECIFICATIONS  
Actual  
Ship.  
Output (Gallons)  
Recovery  
Dimensions In Inches  
Storage  
Capacity  
U.S.  
Input  
Rating  
BTU/Hr.  
Firing  
Rate  
GPH  
Wt.  
w/Burner  
(lbs.)  
Motor HP  
120V 60 Hz 1  
Model Number  
Gallons  
80°F Rise 100°F Rise 140°F Rise  
A
B
C
D
E
F
G
H
J
1
TPD 150 140 ONEA  
TPD 150 199 ONEA  
TPD 150 255 ONEA  
TPD 150 270 ONEA  
TPD 150 400 ONEA  
TPD 150 540 ONEA  
TPD 150 720 ONEA  
TPD 200 300 ONEA  
TPD 200 600 ONEA  
TPD 200 800 ONEA  
TPD 200 1000 ONEA  
TPD 200 1250 ONEA  
TPD 200 1500 ONEA  
TPD 300 300 ONEA  
TPD 300 600 ONEA  
TPD 300 800 ONEA  
TPD 300 1000 ONEA  
TPD 300 1250 ONEA  
TPD 300 1500 ONEA  
TPD 400 600 ONEA  
TPD 400 800 ONEA  
TPD 400 1000 ONEA  
TPD 400 1250 ONEA  
TPD 400 1500 ONEA  
TPD 400 1750 ONEA  
TPD 400 2000 ONEA  
TPD 500 2250 ONEA  
TPD 500 2500 ONEA  
TPD 600 720 ONEA  
TPD 600 1000 ONEA  
TPD 600 1250 ONEA  
TPD 600 1500 ONEA  
TPD 600 1750 ONEA  
TPD 600 2000 ONEA  
TPD 600 2250 ONEA  
TPD 600 2500 ONEA  
163  
163  
163  
163  
151  
151  
145  
221  
221  
221  
140,000  
199,000  
255,000  
270,000  
400,000  
540,000  
720,000  
300,000  
600,000  
800,000  
1
170  
241  
309  
327  
485  
654  
873  
364  
727  
136  
193  
247  
262  
387  
524  
698  
291  
582  
776  
970  
1212  
1455  
291  
582  
776  
970  
1212  
1455  
582  
776  
970  
1212  
1455  
1697  
1939  
2182  
2424  
698  
97  
138  
176  
187  
277  
374  
416  
208  
416  
554  
693  
866  
1039  
208  
416  
554  
693  
8312 14  
8312 14  
8312 14  
8312 14  
8312 14  
8312 14  
2  
2  
2  
2734 114 3612  
2734 114 3612  
2734 114 3612  
2734 114 3612  
2734 114 3612  
2734 114 3612  
5
6
6
6
7
8
47 73  
47 73  
47 73  
5712 73  
5712 73  
5712 73  
1292  
1292  
1292  
1397  
1397  
1505  
1510  
2098  
2098  
2103  
2103  
2467  
2757  
2150  
2150  
2308  
2308  
2584  
2774  
3207  
3212  
3212  
3212  
3402  
3528  
3669  
1
1
1.4  
1.8  
1.9  
2.8  
3.8  
5.1  
2.1  
4.2  
5.7  
1
7  
HP - 4.4 Amp  
1
1
1
8312 14 114 2734 114 3612 10 5712 73  
4
3
HP - 4.6 Amp  
HP - 5.5 Amp  
1
1
8312 15  
8312 15  
1
1
3212 112 4434  
3212 112 4434  
6
8
6612 73  
6612 73  
970  
8312 15 114 3212 112 4434 10 6612 73  
8312 15 114 3212 112 4434 10 6612 73  
8312 15 114 3212 112 4434 12 6612 73  
8312 15 112 3212 112 4434 12 8112 73  
201 1,000,000 7.1  
201 1,250,000 8.9  
201 1,500,000 10.7  
300  
300  
300  
300 1,000,000 7.1  
300 1,250,000 8.9  
300 1,500,000 10.7  
411  
411  
411 1,000,000 7.1  
411 1,250,000 8.9  
397 1,500,000 10.7  
397 1,750,000 12.5  
397 2,000,000 14.2  
495 2,250,000  
495 2,500,000 17.8  
594 720,000 5.1  
594 1,000,000 7.1  
594 1,250,000 8.9  
594 1,500,000 10.7  
594 1,750,000 12.5  
594 2,000,000 14.3  
1212  
1515  
1818  
364  
727  
970  
1212  
1515  
1818  
727  
3
3
3
4
HP - 10.2 Amp  
HP - 4.6 Amp  
300,000  
600,000  
800,000  
2.1  
4.2  
5.7  
9112 14  
9112 14  
1
1
2612 112 4434  
2612 112 4434  
6
8
6612 83  
6612 83  
1
4  
9112 14 114 2612 112 4434 10 6612 83  
9112 14 114 2612 112 4434 10 6612 83  
9112 14 114 2612 112 4434 12 6612 83  
9112 14 112 2612 112 4434 12 8112 83  
1
3  
HP - 5.5 Amp  
866  
1039  
416  
554  
693  
4
HP - 10.2 Amp  
HP - 4.6 Amp  
1
600,000  
800,000  
4.2  
5.7  
9112 15  
1
3212  
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
55  
8
7612 81  
4  
970  
9112 15 114 3212  
9112 15 114 3212  
9112 15 114 3212  
9112 15 112 3212  
55 10 7612 81  
55 10 7612 81  
55 12 7612 81  
55 12 9112 81  
55 14 9112 81  
55 14 9112 89  
1
1212  
1515  
1816  
2121  
2424  
2727  
3030  
873  
1212  
1515  
1816  
2121  
2424  
2727  
3030  
3  
HP - 5.5 Amp  
866  
1039  
1212  
1385  
1558  
1732  
499  
693  
866  
1039  
1212  
1385  
1558  
1732  
9112 15  
9912 15  
110 15  
110 15  
2
2
2
2
3212  
3212  
3212  
3212  
4  
HP - 10.2 Amp  
16  
55 16 9112 100 4277  
55 16 9112 100 4419  
55 10 7612 109 3667  
55 10 7612 109 3667  
55 12 7612 109 3667  
55 12 9112 109 3837  
55 14 9112 109 3837  
55 14 9112 109 3837  
55 16 9112 109 4477  
55 16 9112 109 4619  
1 HP - 16 Amp  
119 15 114 3212  
119 15 114 3212  
119 15 114 3212  
119 15 112 3212  
1
4
3
HP - 4.6 Amp  
HP - 5.5 Amp  
970  
1
1212  
1455  
1697  
1939  
2182  
2424  
3
119 15  
119 15  
119 15  
119 15  
2
2
2
2
3212  
3212  
3212  
3212  
4  
HP - 10.2 Amp  
575 2,250,000  
575 2,500,000 17.8  
16  
1 HP - 16 Amp  
Certified Minimum Installation Clearances to Combustibles:  
Front: 18 inches  
Back: 0 inches  
Sides: 0 inches  
Top: 5 inches  
A clearance of 24 inches should be maintained from  
serviceable parts such as relief valve, power burner, drain  
valve and anodes (anodes are located on side above cold  
water inlet).  
State Titan TPD models are Category I appliances  
(Fan Assisted) and require a negative draft. These units  
should only be commonly vented with other Category I  
negative draft appliances per the latest addition of the  
National Fuel Gas Code. An approved/listed Type “B” venting  
material is recommended. A negative draft of -0.02˝ to -0.07  
is required in the vent.  
ASME  
COMMERCIAL  
The Expert’s Choice®  
 
Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters  
SUGGESTED SPECIFICATIONS  
TM  
TITAN LV POWER GAS (MODELS TPG)  
Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design  
and include a powered gas burner with electronic flame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure  
regulator, diaphragm air switch for proof of blower operation, and flame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input  
rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall  
be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, and stamped National  
Board, and listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination  
temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for  
easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s)  
must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efficiency and standby loss. The outer jacket shall have a baked powder coat finish. All internal  
surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by firing at a  
temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional  
start-up service to be included.  
SUGGESTED SPECIFICATIONS  
TM  
TITAN LV POWER LOW NOX (MODELS TPX)  
Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design  
and include a powered gas burner with electronic flame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure  
regulator, diaphragm air switch for proof of blower operation, and flame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input  
rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall  
be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, ASME stamped and listed  
by Underwriters Laboratories. The water heater shall be approved for low NOx and meet or exceed California rule 1146.2. The unit shall provide modulating fire for  
smooth system operation and precise temperature control. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, modulating  
control, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door  
shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam  
insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efficiency and standby loss. The outer jacket shall have a baked powder coat  
finish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel  
by firing at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty.  
Professional start-up service to be included.  
SUGGESTED SPECIFICATIONS  
TITAN LV POWER OIL AND DUAL FUEL (MODELS TPO AND TPD)  
TM  
Water heater(s) shall be Model_____________________as manufactured by the State Water Heaters or an approved equal. Heater(s) shall have a minimum oil firing  
rate of_____gallons per hour, an input rating of____________BTU/HR. The heater(s) shall have a recovery rate of_____GPH at a 100°F rise and a storage capacity  
of______gallons. The 160 psi design pressure tank shall be glass-lined with an alkaline borosilicate composition and fused to the steel by firing at 1600°F. The heater(s)  
shall be equipped with______NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, and carry a National Board stamping. The heater(s) shall be ASME and the  
entire unit listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination  
temperature and pressure gauge, low water cutoff, ASME rated temperature and pressure relief valve, and barometric draft regulator. Control compartment door shall  
be hinged for easy access and include cam locks for security. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be  
insulated with high-density foam insulation and meet or exceed current standard of ASHRAE 90.1-1999 for standby loss and recovery efficiency. The heater(s) shall  
include a drain valve and flame observation port. The jacket shall be baked powder coat finish. Heater(s) vessel shall have a 3, 5 or 10 year limited warranty against  
failure as outlined in the written warranty.  
The TPO models shall have a UL listed burner with two-stage pump, oil safety valve, electronic flame safeguard, intermittent ignition and diaphragm air switch for proof  
of flame operation.  
The TPD models shall include a dual fuel burner with two-stage oil pump, oil safety valve, electronic flame safeguard, intermittent ignition, diaphragm air switch, main  
and pilot automatic gas valves, gas pressure regulator and manual crossover switch.  
In keeping with our policy of continuous product improvement,  
specifications are subject to change without prior notice.  
Printed in U.S.A.  
STPBGODF/1003  
COMMERCIAL  
The Expert’s Choice®  
©2003 State Water Heaters  
 

Sennheiser Marine RADAR SZT 1011 User Manual
Sharp Microwave Oven R 890N User Manual
Sony Microcassette Recorder ICD PX333 User Manual
Sony Portable Speaker SRS A17 User Manual
Speco Technologies DVR DVR 16TL 160 User Manual
Speco Technologies Portable Speaker SP 150T User Manual
Sterling Water System SGM 250A User Manual
Swisher Lawn Mower ZT2350A User Manual
Symphonic TV DVD Combo BL519DD User Manual
Talk electronic CD Player Thunder 22 User Manual